SUPREX POLYESTER FABRIC
Special fabrics for screen printing, for precision filtration and for industrial applications where high accuracy textile micronets are needed. SUPREX is a Monofilament Polyester Fabric specifically designed for Screen printing Applications. The SUPREX range includes coarse fabric for printing high density inks, glitters, flocking and finer fabric for printing UV inks and high definition prints.
Complementary accessories.
Set for use during the preparation of flat and round screens
|
CODE |
DESCRIPTION AND USE |
| AQSSEEDKIT | SEEDKIT – ACCESSORIES FOR SCREEN MAKING LABORATORY (COMPLETE SET OF THE BELOW ITEMS) |
| ARCARG1010L05 | GRADUATED CARAF 10X10 L. 0.5 (TO DOSE LIQUID PRODUCTS) |
| ARCCGB817ML100 | SHORT GRADUATED CYLINDER 817 – ML 100 (TO MEASURE CHEMICALS) |
| ARCCGB820ML250 | SHORT GRADUATED CYLINDER 820 – ML 250 (TO MEASURE CHEMICALS) |
| AGDCARTIGLIO | CLAW CUTTER (TO CUT FILMS, STRETCHED FRAMES, SCREENS, ETC.) |
| AGDCD400PCLR | CUTTER D400 P WITH SPARE BLADES (TO CUT FILMS, STRETCHED FRAMES, SCREENS, ETC.) |
| AGDDISPNA3366 | ADHESIVE ROLL TAPE DISPENSER 33/66M (DISPENSER FOR ADHESIVE TAPE) |
| ARCFLV3M | FLEXOMETER VOLA 3 METER LENGTH (FOR SEVERAL MEASUREMENTS) |
| AGDFORLAB6P | 6 INCHES LASER SCISSOR (TO CUT FABRICS, FILMS, DESIGNS ON PAPER, ETC.). |
| ARCGGAA | RUBBER ANTI-ACID GLOVES (TO WEAR WHEN USING CORROSIVE OR FLAMMABLE PRODUCTS) |
| AGDKITLAMR9MM | KIT 10 SPARE BLADES 9 MM FOR CLAW CUTTER (SPARE BLADES FOR CUTTER) |
| AQSLEN1010 | 10X10 MESH COUNTER (TO CONTROL DESIGNS, FILMS, FABRICS OR FINISHED SCREENS) |
| AGDNASCRYCL1966 | ADHESIVE TAPE CRYSTAL CLEAR MM 19X66 MT |
| AQSPELEXP | EXPOSURE CALCULATOR FILM (TO CONTROL ENGRAVING ANGLES) |
| AGDPENSSFBLU | STABILO OH PEN SUPERFINE PERMANENT BLUE (TO WRITING ON FILMS) |
| ARCPPACR | NYLON BRUSH 40 MM ( TO CLEAN OR DEGREASE THE FABRICS) |
| ARCPSB30MM | BLOND BRISTLE BRUSH 30 MM (TO APPLY PRODUCTS OR TO MAKE FINISHING) |
| ARCPSN50MM | BLACK BRISTLE BRUSH 50 MM (TO APPLY PRODUCTS OR TO MAKE FINISHING) |
| ARCPSN60MM | BLACK BRISTLE BRUSH 60 MM (TO APPLY PRODUCTS OR TO MAKE FINISHING) |
| ARCRIGTGRAD80 | T RULER PERSPEX NEUTRAL -MOVING HEAD- GRAD. CM. 80, (TO CONTROL ANGLES AND LINES) |
| AQSSBAN111 | RETOUCHING SPATULA FINE ARTS NO. 111, (FOR FINISHING AND FILLER APPLICATION) |
| ARCSPRZPL500CC | PLASTIC SPRAY BOTTLE 183 – 500 ML (FOR SEVERAL LIQUIDS) |
| ARCSSG | GIANT SYNTHETIC SPONGE (FOR ACCESSORIES OR EQUIPMENT CLEANING) |
The PVC tank is used for manual processing flat or round screens after the exposure step.
RECOMMENDED ACCESSORIES
Water jet pump; water vacuum extractor
TECHNICAL CHARACTERISTICS
The supporting frame is made of painted steel
The tank is made of acid-resistant PVC, electro-welded with robust edges
Provided with spray unit and tap fitting
Frame or cylinder supporting grid
Central lighting viewer (CV models) for processing control
AVAILABLE MODELS
SV without the central viewer
CV with the central viewer
CVRA (on demand) with water re-cycling system and bottom wheel carriage tank
| CODE | NAME | MODEL | USEFUL SIZE CM. | OVERALL DIMENSIONS CM. |
|
AQSVCV070100 |
PVC DEVELOPING TANK |
CV-0710 |
70X100 |
106X95X176 H. |
|
AQSVSV070100 |
PVC DEVELOPING TANK |
SV-0710 |
70X100 |
106X95X176 H. |
|
AQSVCV075200 |
PVC DEVELOPING TANK |
CV-0752 |
75X200 |
205X100X222 H. |
|
AQSVSV075200 |
PVC DEVELOPING TANK |
SV-0752 |
75X200 |
205X100X222 H. |
|
AQSVCV100140 |
PVC DEVELOPING TANK |
CV-1014 |
100X140 |
145X125X185 H. |
|
AQSVSV100140 |
PVC DEVELOPING TANK |
SV-1014 |
100X140 |
145X125X185 H. |
|
AQSVCV120160 |
PVC DEVELOPING TANK |
CV-1216 |
120X160 |
165X145X185 H. |
|
AQSVSV120160 |
PVC DEVELOPING TANK |
SV-1216 |
120X160 |
165X145X185 H. |
Seedex photoexposer is a three-function machine for drying and exposing screen printing frames.
MACHINE’S DESCRIPTION AND CHARACTERISTICS:
Painted steel structure
The machine is equipped with a dryer with drawers located in the bottom part of the machine, with a pneumatic press in the central part, and a halogen lamp located in the upper part.
The Pneumatic press is available in 2 versions:
manual opening (model TC) and
automatic opening (model TC-A);
Dryer with 3 drawers sliding on bearings to dry photosensitive emulsion before exposure,
Completed with a UV ray protection system consisting of a rigid casing with a self-winding front curtain and sliding side panels for inspection.
The control panel consists of a 29 channel digital computer that can control and store exposure times, vacuum times, and the drying kiln temperature and display the number of hours the bulb has been operating in order to monitor its lifetime.
Exposure compensating light with photocell
A vacuum meter is installed on the control panel that allows the pressure control in the vacuum table
The cooling system include preventing overheating of electrical components
Metal-halogen lamp in 2 versions: 2000/5000 W or 3500/7000 W
POWER SUPPLY
400 V – 50 Hz (3 phases + earth) – 10000 W, with variations possible on request
RECOMMENDED SPARE PARTS
halogen bulb 5000 or 7000 W depending on the models
rubber mat with a sealed edge sized to the pneumatic press
|
CODE NUMBER |
PHOTOEXPOSER TC (MANUAL PNEUMATIC PRESS OPENING) |
GLASS SIZE CM. |
USEFUL SIZE CM. |
OVERALL DIMENSION CM. |
| AQSFOTTC1 |
PHOTOEXPOSER TC 1 |
90X110 |
70X95 |
150X130X260 H |
| AQSFOTTC2 |
PHOTOEXPOSER TC 2 |
123X153 |
100X135 |
190X165X260 H |
| AQSFOTTC3 |
PHOTOEXPOSER TC 3 |
143X173 |
120X155 |
210X180X260 H |
| AQSFOTTC4 |
PHOTOEXPOSER TC 4 |
160X200 |
140X180 |
235X195X260 H |
| AQSFOTTC5 |
PHOTOEXPOSER TC 5 |
140X220 |
120X200 |
258X178X300 H |
|
CODE NUMBER |
PHOTOEXPOSER TC-A (AUTOMATIC PNEUMATIC PRESS OPENING) |
GLASS SIZE CM. |
USEFUL SIZE CM. |
OVERALL DIMENSION CM. |
| AQSFOTTCA1 |
PHOTOEXPOSER TC-A1 |
90X110 |
70X95 |
150X130X260 H |
| AQSFOTTCA2 |
PHOTOEXPOSER TC-A2 |
123X153 |
100X135 |
190X165X260 H |
| AQSFOTTCA3 |
PHOTOEXPOSER TC-A3 |
143X173 |
120X155 |
210X180X260 H |
| AQSFOTTCA4 |
PHOTOEXPOSER TC-A4 |
160X200 |
140X180 |
235X195X260 H |
| AQSFOTTCA5 |
PHOTOEXPOSER TC-A5 |
140X220 |
120X200 |
258X178X300 H |
Made by painted stainless steel, with manual closing clamps.
All movements are effected by 2 driving handwheels plus the beam’s one;
Complete of n ° 3 pression bars and all accessories.
The TME “multistretcher” is a mesh tensioning unit for the professionals.
It allows stretching mesh on many frames of different formats and profiles at the same time.
The waste of mesh is minimized and the most economical production is guaranteed.
The frames can be stretched straight or at any angle with synthetic mesh, metallised polyester as well as stainless steel mesh to produce reproducible stencils for all printing purposes.
Due to the handwheels and beam movements of all 3 sides, a parallel, even mesh tension of warp and weft is guaranteed; the uniform stretching over the entire area is maintained by the clamps on all three sides which are riding independently on roller bearings.
Frame contact with the mesh again is manually driven for easy handling.
| CODE | NAME | MODEL | USEFUL FRAME SIZE CM. | OVERALL DIMENSION CM. |
| AQSTME1330PM | MANUAL STRETCHING MACHINE | TME 130X300 |
130X300 |
390X186XH112 |
|
AQSTME1630PM |
MANUAL STRETCHING MACHINE |
TME 160X300 |
160X300 |
390X216XH112 |
|
AQSTME1830PM |
MANUAL STRETCHING MACHINE |
TME 180X300 |
180X300 |
390X236XH112 |
|
AQSTME2030PM |
MANUAL STRETCHING MACHINE |
TME 200X300 |
200X300 |
390X256XH112 |